+966 12 690 2144 / +971 4 5149230

PA to Fiber Conversion

We’ve been receiving numerous requests for converting PROFIBUS PA to fibre optics lately. I believe that really what the request is that there is an existing PROFIBUS DP master with DP (and possible existing PA) infrastructure and the requirement is to add some PA devices that are out in the field. PROCENTEC have a range of COMbricks modules that are able to meet almost any type of network configuration. In this article we’ll investigate some of the configuration options and which components should be used in each configuration. Your network layout might look something like the picture below:

 

PA-to-Fiber01

 

Being able to run fibre to these field areas has the following advantages:

 

  • Fibre can be run over longer distances, PROCENTEC offer up to 30km on single-mode fibre. Typically, 2km on multi-mode.
  • Fibre can run through areas that are susceptible to EMC interference without being affected
  • The inherent electrical isolation means that the complicated story of earthing on PA systems is simplified to just the field area. In other words, the complication of Earth loop current over long distance is avoided.

 

Before going ahead with the design, one needs to answer some questions:

 

  • Will multi-mode or single-mode fibre be used? Or is there a mixture?
  • What connector types will be used on the fibre?
  • Is a fibre redundant ring required?

 

Before going ahead with the design, one needs to answer some questions:

 

Multi-mode off one COMbricks fibre module in the substation (1 is spare):

 

PA-to-Fiber02

 

COMbricks components used in above implementation:

 

  • x3 Head Station Type 1B (101-20011B)
  • x3 PROFIBUS Fiber Optic Module (101-201510)
  • x2 PROFIBUS PA link/coupler Module (101-201610)
  • x2 SCOPE Repeater (101-201210) for connection the DP devices in the substation

 

Multi-mode off one COMbricks fibre module in the substation (1 is spare), redundant ring:

 

PA-to-Fiber02

 

COMbricks components used in above implementation:

 

  • x3 Head Station Type 1B (101-20011B)
  • x3 PROFIBUS Multi-Mode Fiber Optic Ring Module (101-201530)
  • x2 PROFIBUS PA link/coupler Module (101-201610)
  • x2 SCOPE Repeater (101-201210) for connection the DP devices in the substation

 

Multi-mode off one COMbricks fibre module in the substation, redundant ring for each field area:

 

PA-to-Fiber03

 

COMbricks components used in above implementation:

 

  • x3 Head Station Type 1B (101-20011B)
  • x4 PROFIBUS Multi-Mode Fiber Optic Ring Module (101-201530)
  • x2 PROFIBUS PA link/coupler Module (101-201610)
  • x2 SCOPE Repeater (101-201210) for connection the DP devices in the substation

 

All of the above implementations could be implemented using single mode fibre. Simply replace the multimode fibre module with the Single-Mode Fiber Optic Ring (101-201531).

 

It is possible to mix multi-mode and single-mode using the PROFIBUS Multi-Mode and Single-Mode Fiber Optic Ring module (101-201532):

 

PA-to-Fiber04

 

COMbricks components used in above implementation:

 

  • x3 Head Station Type 1B (101-20011B)
  • x1 Multi-Mode and Single-Mode Fiber Optic Ring module (101-201532) in substation
  • x1 PROFIBUS Multi-Mode Fiber Optic Ring Module (101-201530) for area 3
  • x1 Single-Mode Fiber Optic Ring (101-201531) for area 2
  • x2 PROFIBUS PA link/coupler Module (101-201610)
  • x2 SCOPE Repeater (101-201210) for connection the DP devices in the substation

 

COMbricks is a modular network component solution with flexibility to meet almost any type of network architecture. All COMbricks head stations can be connected to the local LAN and be used to remotely access and view the health of the segments the COMbricks modules are attached to. They can even be configured to issue email alerts if a PROFIBUS error has been detected on the segment so that it can be addressed before it causes a failure. This is part of your pre-emptive maintenance strategy.

 

@ IDX

LATEST FROM BLOG AND NEWS
  ASM attended IMECO World Sales Meeting 2017 for meeting the complete sales network and discuss future opportunities and how to improve in sales & in technical for weighing and bagging.   IMECO has been in the market for more
  Date: 23 – 25 Oct. 2017   Location: Dubai   Website: https://www.wetex.ae/   ASM with its Partners (Siemens, PROCENTEC, Iba-Gulf and Training for Industry) are participating to show their client ne
  ASM celebrated its 10th Anniversary internally. Coming from all over the region to Dubai for improving the new outcome and how things can be better for 2018 on-wards...
Contact us...
P.O.Box 51736,Al-Khalidiah Dist.,
Al-Ghaya st. - Villa no.6, Jeddah 21553
info@asm.net
Fax :
+966 12 690 2209
JEDDAH
+966 12 690 2144
KHOBAR
+966 13 895 0910
RIYADH
+966 11 491 1104
DUBAI
+971 45 149 230
P.O.Box 51736,Al-Khalidiah Dist.,
Al-Ghaya st. - Villa no.6, Jeddah 21553
info@asm.net
Fax :
+966 12 690 2209
JEDDAH
+966 12 690 2144
KHOBAR
+966 13 895 0910
RIYADH
+966 11 491 1104
DUBAI
+971 45 149 230
We're social too...